Enable On/Off Mode

Hold Up + Tap Config 3x

Effect: Solid · Color: Red

If the switch has successfully been switched over to an on/off switch, the LED Bar will flash Red.

Enable Dimmer Mode

Hold Down + Tap Config 3x

Effect: Solid · Color: Orange

If the switch has successfully been switched over to a dimmer switch, the LED Bar will flash Orange.

Enable Smart Bulb Mode

Hold Up + Tap Config 4x

Effect: Solid · Color: Yellow

If the switch has successfully enabled Smart Bulb Mode, the LED Bar will flash Yellow.

Disable Smart Bulb Mode

Hold Down + Tap Config 4x

Effect: Solid · Color: Blue

If the switch has successfully disabled Smart Bulb Mode, the LED Bar will flash Blue.

Enable Multi-Way + Aux Switch Mode

Hold Up + Tap Config 5x

Effect: Solid · Color: White

If the switch has successfully enabled Multi-Way + Aux Switch Mode, the LED Bar will flash White.

Enable Multi-Way + Dumb Switch Mode

Hold Down + Tap Config 5x

Effect: Solid · Color: Violet

If the switch has successfully enabled Multi-Way + Dumb Switch Mode, the LED Bar will flash Violet.

Enable Single Pole Mode

Hold Up + Tap Config 6x

Effect: Solid · Color: Cyan

If the switch has successfully enabled Single Pole Mode, the LED Bar will flash Cyan.

Enable Single Pole Mode – Full Sine Wave

Hold Down + Tap Config 6x

Effect: Solid · Color: Green

If the switch has successfully enabled Single Pole Mode – Full Sine Wave, the LED Bar will flash Green.

Enable Instant On (Button Delay Disabled)

Hold Up + Tap Config 7x

Effect: Solid · Color: Green

If the switch has successfully enabled Instant On, the LED Bar will flash Green.

Disable Instant On (Button Delay Enabled)

Hold Down + Tap Config 7x

Effect: Solid · Color: Yellow

If the switch has successfully disabled Instant On, the LED Bar will flash Yellow.

Enable Audible Relay Click

Hold Up + Tap Config 8x

Effect: Solid · Color: Cyan

If the switch has successfully enabled the Audible Relay Click, the LED Bar will flash Cyan.

Disable Audible Relay Click

Hold Down + Tap Config 8x

Effect: Solid · Color: Pink

If the switch has successfully disabled the Audible Relay Click, the LED Bar will flash Pink.

Show Firmware Version

Hold Down + Config 9x

Effect: Long Blink, Short Blink · Color: White, Orange

The Dimmer switch LED Bar will blink white for major firmware versions and orange for minor firmware versions, with long blinks being for 10's and short blinks for 1's.

Example: firmware 2.15 → long blink white twice (2.15), then long blink once (2.15) followed by five short blinks (2.15).

Enable Local Protection Mode

Hold Up + Tap Config 10x

Effect: Solid · Color: Green

If the switch has successfully enabled Local Protection Mode, the LED Bar will flash Green.

Disable Local Protection Mode

Hold Down + Tap Config 10x

Effect: Solid · Color: Red

If the switch has successfully disabled Local Protection Mode, the LED Bar will flash Red.

Enable Leading Edge For Dimming

Hold Up + Tap Config 13x

Effect: Solid · Color: Pink

If the switch has successfully enabled Leading Edge Dimming, the LED Bar will flash Pink.

Enable Trailing Edge For Dimming

Hold Down + Tap Config 13x

Effect: Solid · Color: Indigo

If the switch has successfully enabled Trailing Edge Dimming, the LED Bar will flash Indigo.

Check Thread Network Strength at your switch's location

Hold Config Button for 5–10 seconds

Effect: Solid · Color: Green

When the LED Bar turns Green, release the config button and note the color of the LED Bar signifying signal strength.

Green = Strong
Yellow = Fair
Red = Poor

Factory Reset your Switch

Hold Config Button + Top of the Paddle (On Button) for ~20 seconds

Effect: Solid · Color: Red

If successful in factory resetting your switch, the LED Bar will turn Red. If it turns purple, try again and make sure to hold down both the top of the paddle and the config button at the same time.